XDS H.100 PCI T1 / E1 Board
 



 
 


Product Part Number:

257L119 : 4-Span T1 Interface Board (with voice resources, conferencing)
257L074 : 4-Span T1 Interface Board (without voice resources or conferencing)
257L120 : 8-Span T1 Interface Board (with voice resources)
257L131 : 8-Span T1 Interface Board (without voice resources)

257L121 : 4-Span E1 Interface Board (with voice resources, conferencing)
257L132 : 4-Span E1 Interface Board (without voice resources, conferencing)
257L122 : 8-Span E1 Interface Board (with voice resources)
257L133 : 8-Span E1 Interface Board (without voice resources)

PC Form Factor: PCI
TDM Bus Type: H.100
Digital Line Interface: Primary Rate ISDN / T1 / E1 Spans

The XDS 4-span and 8-span T1/E1 boards offer a selectable 75ohm/120ohm E1 interface or a 100ohm T1 interface. Call progress tone generation and DTMF tone generation/detection are supported. Status LEDs are provided on each port for red, yellow, and blue alarm conditions. D4 and ESF signaling are supported for T1 interfaces, and CRC4 and non-CRC4 signaling are supported for E1 interfaces. Primary Rate ISDN is supported, including access to either layer 2 or layer 3 from the application level. Driver support includes Linux, Windows 2000, Windows NT, and UnixWare.

Boards ordered with optional voice resources include 128 channels of bi-directional voice resources (4-span boards) or 256 channels of voice resources (8-span boards), as well as two analog inputs for music-on-hold applications.
4-span T1/E1 boards also include 128 ports of enhanced conferencing.

Click here to download the H.100 T1/Primary Rate ISDN technical manual

Click here to download the H.100 E1/Primary Rate ISDN technical manual

  
Additional Product Specifications

PRI Interfaces:
(23 B channels + 1 D channel) x 8 spans
Each span is software selectable as Network Termination (NT) or Terminal Equipment (TE)

T1 Interfaces:
(24 channels) x 8 spans
Each span is software selectable as Customer Premise Equipment (CPE) or Central Office (CO)

E1 Interfaces:
(30 channels) x 8 spans
Each span is software selectable as Customer Premise Equipment (CPE) or Central Office (CO)

Framing: (all options are software selectable per port)
T1 Framing: D4, ESF
E1 Framing: CRC4, non-CRC4

T1 Zero Suppression: AMI, B8ZS
E1 Zero Suppression: AMI, HDB3

T1 Signaling: Robbed Bit, PRI
E1 Signaling: CAS, PRA

Line Protocols:
T1 Line Type: E&M, Ground Start, Loop Start
E1 CAS Line Type: E&M, Ground Start, Loop Start, Q.421
Direction: FXO, FSX
Optional Address Protocol: Immediate Start, Wink Start

PRI Signaling Protocols:
Layer 2 and Layer 3 messaging supported
Layer 3 protocol stacks: NI-1, elements of NI-2 and NI-3, ANSI T1.407, ANSI T1.410, ETSI 102


DSP Resources:
DTMF Detector (each B-channel)
Energy Detector (each B-channel)
DTMF Generator (each B-channel for signaling)
Call Progress Tone Generation (each B-channel)
1004Hz Calibration Tone Generation
Optional Voice Resources:
Channels: 128 or 256 (for 4-span or 8-span boards, respectively)
Audio file formats supported: A-law, Mu-law, 6/8kHz ADPCM, .WAV, 16-bit linear PCM
Playback Halt Upon DTMF Detection: Supported

Optional Conference Resources (4-span boards):
4-span T1/E1 Boards ordered with Voice Resource modules include 128 ports
of enhanced conferencing with DTMF tone clamping.

Optional Music-On-Hold Ports:
4-span or 8-span boards ordered with Voice Resource modules include 2 analog input ports for music-on-hold applications.

MVIP/SCSA Legacy Mode:
TDM adapters are available to adapt the H.100 edge connector to standard MVIP or SCSA ribbon cable headers. Legacy modes are initialized via software to adjust TDM clocks to 2.048MHz (MVIP) or 4.096MHz (SCSA) accordingly.

 Temperature Extremes:
Operating: 0°C (+32°F) to +50°C (+122°F)
Storage: -40°C (-40°F) to +70°C (+158°F)

Ambient Humidity:
Designed to withstand ambient relative humidity from 0% to 95% non-condensing in both operating and storage conditions.

Mechanical:
Designed to conform to PCI-SIG mechanical specifications for full-length PCI cards.

MTBF:
50,000 hours

Electrical Requirements:
+5 volts +5% @ 1.5 amps maximum
+12 volts, +3 volts, and -5 volts are not required.